End Profile - Silver

End Profile Silver

• Laminate Accessories
• End Moulding, Silver
• PGENPSILVME270

• Suitable for height differences of 0 – 12.3 mm.
• End Moulding, Silver

End Profile Silver 9,5 mm Floors

• Laminate Accessories
• End Profile Silver 9,5 mm Floors
• NEENP9SILVME270

• Aluminium profile, silver tone.
• Aluminium profile, silver tone.

Stair Profile Silver

• Laminate Accessories
• Stair Profile, Silver
• PGSTPSILVME250

• Stair nose. Fits flooring thickness 7 – 15 mm. Colour: silver. Surface: aluminium.
• Stair Profile, Silver

Commercial Low Ramp Profile Silver

• Laminate Accessories
• Low Ramp Profile
• PGRPC55SILVME315A

• Ramp profile (adaptor), no screws. Fits to flooring thickness of 8 - 9 mm. With EPDM moulding and plastic connectors. Surface: aluminium.
• Low Ramp Profile

Pre-cut Corner for High Ramp Profile

• Laminate Accessories
• Pre-cut Corner for High Ramp Profile
• PGRPC85CORNSILVME

• Pre-cut Corner for High Ramp Profile, without screws. 90°
• Pre-cut Corner for High Ramp Profile

Adapter Profile

• Vinyl Accessories
• Adapter Profile - Silver
• NEVADPSILV

• This very slim and elegant profile can be used to make the transition between a higher and a lower floor. Can be used with clicked vinyl floors. Wear-resistant quality aluminium. Installation with the supplied subprofile. Glue the sub-profile to the subfloor, then press the adapter profile into the subprofile. Tip: use a hammer and e.g. the tapping block as a help to press the adapter profile in the subprofile.
• Adapter Profile

• Laminate Accessories
• Pre-cut Corner for Low Ramp Profile
• PGRPC55CORNSILVMEA

Commercial End Profile Silver

• Laminate Accessories
• End Moulding, silver
• PGENPCSILVME270

• End moulding, Silver. Fits to flooring thickness of 9 and 10 mm. Surface: aluminium.
• End Moulding, Silver

Expansion Profile

• Vinyl Accessories
• Expansion Profile - Silver
• NEVEXPSILV

• This very slim and elegant profile can be used to cover the expansion joint between 2 floors of the same height e.g. at a door entrance or in a large room/corridor where an expansion joint is required. Can be used with Vinyl Click (+) floors. Wear-resistant quality aluminium. Installation with the supplied subprofile. Glue the sub-profile to the subfloor, then press the expansion profile into the subprofile. Tip: use a hammer and e.g. the tapping block as a help to press the expansion profile in the subprofile.
• Expansion Profile

• Laminate Accessories
• Stair Profile Silver 9,5 mm Floors
• NESTP9SILVME25

Multifunctional Profile Silver

• Laminate Accessories
• Combi moulding
• PGPRSILV

• T-moulding and reducer in one. Plastic bottom rail. Suitable for height differences of 0 - 12.3 mm.
• Combi moulding

Commercial Ramp Profile Silver - Drilled

• Laminate Accessories
• Ramp Profile, Drilled
• PGRPC80SILVME270

• Ramp profile, drilled. Flexible in height. For flooring thickness (including underlay): 9 - 15 mm. Extremely resistant aluminium profile.
• Ramp Profile, Drilled

Adapter Profile, commercial

• Vinyl Accessories
• Adapter Profile Commercial Use
• NEVRADPCOMSILV

• Subtle and elegant profile for use in commercial areas. Use the profile to make the transition between a higher and a lower floor, e.g. at a door entrance. Can be used with clicked Vinyl floors. Extra wear-resistant quality aluminium, silver tone. Installation with the supplied screws and plugs (installation without sub-profile). Screw at an angle of 90° into the subfloor (see technical drawing above). Tip: avoid fixing the floor too firmly between the adapter profile and the subfloor. Make sure you can still slide a piece of paper between the profile and the Vinyl floor.
• Adapter Profile Commercial Use

Bendable End Moulding

• Laminate Accessories
• Bendable End Moulding
• NEBENDPCSILVME270

• For finishing laminate "islands" in curved shapes. Surface: anodized aluminium. To be installed with special bending tool (NEBTOOL).
• Bendable End Moulding

Commercial High Ramp Profile Silver

• Laminate Accessories
• High Ramp Profile
• PGRPC85SILVME315

• Ramp profile (adaptor), no screws. Fits to flooring constructions of 22 mm. With EPDM moulding and plastic connectors. Surface: aluminium.
• High Ramp Profile

• Laminate Accessories
• Stair Profile Silver 7-8 mm Floors
• NESTPSILVME25

End Profile Silver 7-8 mm Floors

• Laminate Accessories
• End Profile Silver 7-8 mm Floors
• NEENPSILVME270

• Aluminium profile, silver tone.
• Aluminium profile, silver tone.

Commercial Expansion Profile Silver

• Laminate Accessories
• T-profile, silver
• PGEXPCSILVME270

• T-moulding, Silver. Flexible in height. Flooring thickness (including underlay): 7 - 12 mm. Surface: aluminium.
• T-Moulding, Silver

End Profile Commercial Use

• Vinyl Accessories
• End Profile Commercial Use
• NEVRENPCOMSILV

• Subtle and elegant profile for use in commercial areas. Use the profile to cover the expansion joint between your Vinyl floor and e.g. a wall, window or threshold, or as a connection to a carpet. Can be used with clicked Vinyl floors. Extra wear-resistant quality aluminium, silver tone. Installation with the supplied screws and plugs (installation without sub-profile). Tip: avoid fixing the floor too firmly between the end profile and the subfloor. Make sure you can still slide a piece of paper between the profile and the Vinyl floor.
• End Profile Commercial Use