End Profile Silver
- Laminate Accessories
- End Moulding, Silver
- PGENPSILVME270
- Suitable for height differences of 0 – 12.3 mm.
- End Moulding, Silver
Expansion Profile - Silver
- Vinyl Accessories
- Expansion Profile
- NEVEXPSILV
- Profiles
Locate a dealer near you
Specifications
This very slim and elegant profile can be used to cover the expansion joint between 2 floors of the same height e.g. at a door entrance or in a large room/corridor where an expansion joint is required. Can be used with Vinyl Click (+) floors. Wear-resistant quality aluminium. Installation with the supplied subprofile. Glue the sub-profile to the subfloor, then press the expansion profile into the subprofile. Tip: use a hammer and e.g. the tapping block as a help to press the expansion profile in the subprofile.
Similar accessories
-
-
End Profile Silver 9,5 mm Floors
- Laminate Accessories
- End Profile Silver 9,5 mm Floors
- NEENP9SILVME270
- Aluminium profile, silver tone.
- Aluminium profile, silver tone.
-
Stair Profile Silver
- Laminate Accessories
- Stair Profile, Silver
- PGSTPSILVME250
- Stair nose. Fits flooring thickness 7 – 15 mm. Colour: silver. Surface: aluminium.
- Stair Profile, Silver
-
Commercial Low Ramp Profile Silver
- Laminate Accessories
- Low Ramp Profile
- PGRPC55SILVME315A
- Ramp profile (adaptor), no screws. Fits to flooring thickness of 8 - 9 mm. With EPDM moulding and plastic connectors. Surface: aluminium.
- Low Ramp Profile
-
Pre-cut Corner for High Ramp Profile
- Laminate Accessories
- Pre-cut Corner for High Ramp Profile
- PGRPC85CORNSILVME
- Pre-cut Corner for High Ramp Profile, without screws. 90°
- Pre-cut Corner for High Ramp Profile
-
Adapter Profile
- Vinyl Accessories
- Adapter Profile - Silver
- NEVADPSILV
- This very slim and elegant profile can be used to make the transition between a higher and a lower floor. Can be used with clicked vinyl floors. Wear-resistant quality aluminium. Installation with the supplied subprofile. Glue the sub-profile to the subfloor, then press the adapter profile into the subprofile. Tip: use a hammer and e.g. the tapping block as a help to press the adapter profile in the subprofile.
- Adapter Profile
-
-
Commercial End Profile Silver
- Laminate Accessories
- End Moulding, silver
- PGENPCSILVME270
- End moulding, Silver. Fits to flooring thickness of 9 and 10 mm. Surface: aluminium.
- End Moulding, Silver
-
-
Multifunctional Profile Silver
- Laminate Accessories
- Combi moulding
- PGPRSILV
- T-moulding and reducer in one. Plastic bottom rail. Suitable for height differences of 0 - 12.3 mm.
- Combi moulding
-
Commercial Ramp Profile Silver - Drilled
- Laminate Accessories
- Ramp Profile, Drilled
- PGRPC80SILVME270
- Ramp profile, drilled. Flexible in height. For flooring thickness (including underlay): 9 - 15 mm. Extremely resistant aluminium profile.
- Ramp Profile, Drilled
-
Adapter Profile, commercial
- Vinyl Accessories
- Adapter Profile Commercial Use
- NEVRADPCOMSILV
- Subtle and elegant profile for use in commercial areas. Use the profile to make the transition between a higher and a lower floor, e.g. at a door entrance. Can be used with clicked Vinyl floors. Extra wear-resistant quality aluminium, silver tone. Installation with the supplied screws and plugs (installation without sub-profile). Screw at an angle of 90° into the subfloor (see technical drawing above). Tip: avoid fixing the floor too firmly between the adapter profile and the subfloor. Make sure you can still slide a piece of paper between the profile and the Vinyl floor.
- Adapter Profile Commercial Use
-
Bendable End Moulding
- Laminate Accessories
- Bendable End Moulding
- NEBENDPCSILVME270
- For finishing laminate "islands" in curved shapes. Surface: anodized aluminium. To be installed with special bending tool (NEBTOOL).
- Bendable End Moulding
-
Commercial High Ramp Profile Silver
- Laminate Accessories
- High Ramp Profile
- PGRPC85SILVME315
- Ramp profile (adaptor), no screws. Fits to flooring constructions of 22 mm. With EPDM moulding and plastic connectors. Surface: aluminium.
- High Ramp Profile
-
-
End Profile
- Vinyl Accessories
- End Profile - Silver
- NEVENPSILV
- This very slim and elegant profile can be used to cover the expansion joint between your Vinyl floor and e.g. a wall, window or threshold, or as a connection to a carpet. Can be used with clicked (+) Vinyl floors. Wear-resistant quality aluminium. Installation with the supplied subprofile. Glue the sub-profile to the subfloor, then press the end profile into the subprofile. Tip: use a hammer and e.g. the tapping block as a help to press the end profile in the subprofile.
- End Profile
-
End Profile Silver 7-8 mm Floors
- Laminate Accessories
- End Profile Silver 7-8 mm Floors
- NEENPSILVME270
- Aluminium profile, silver tone.
- Aluminium profile, silver tone.
-
Commercial Expansion Profile Silver
- Laminate Accessories
- T-profile, silver
- PGEXPCSILVME270
- T-moulding, Silver. Flexible in height. Flooring thickness (including underlay): 7 - 12 mm. Surface: aluminium.
- T-Moulding, Silver
-
End Profile Commercial Use
- Vinyl Accessories
- End Profile Commercial Use
- NEVRENPCOMSILV
- Subtle and elegant profile for use in commercial areas. Use the profile to cover the expansion joint between your Vinyl floor and e.g. a wall, window or threshold, or as a connection to a carpet. Can be used with clicked Vinyl floors. Extra wear-resistant quality aluminium, silver tone. Installation with the supplied screws and plugs (installation without sub-profile). Tip: avoid fixing the floor too firmly between the end profile and the subfloor. Make sure you can still slide a piece of paper between the profile and the Vinyl floor.
- End Profile Commercial Use
Expansion Profile - Silver
- Vinyl Accessories
- Expansion Profile
- NEVEXPSILV
